X

STA HP 3

High Pressure Thermogravimetric / Simultaneous thermal analysis instrument – Table version

Description

On point

Linseis introduced the all new STA HP 3 (TGA+DSC) table top high pressure thermogravimetric, simultaneous thermal analysis instrument. The STA HP 3 is the result of 25 years of experience thermal analysis under high pressure. The superior high speed micro-furnace with a maximum temperature of 1200°C, top loading microbalance, true TG-DSC Thermogravimetry-differential scanning calorimetry design permit exiting new opportunities. The table top design, optional vapor generator and different gas dosing systems provides utmost flexibility.

Worlds only top loading combined TG-DSC (Thermogravimeter and Differential Scanning Calorimeter). For experiments up to 1200°C and up to 150 bar in reactive or inert atmospheres.

Easy user exchangeable TGA or TG-DSC plug and play sensors. The right choice for any given experiment gives you the flexibility to analyze TGA only experiments with volumes up to 1 ml or combined TGA-DSC analysis with up to 0.12 or 0.3 ml volume.

TG-DSC Thermogravimetry-differential scanning calorimetry arrangement permits the combined analysis of weight change and caloric events like endothermal or exothermal reactions or phase transitions in one run and under the same temperature, gas and pressure conditions.

High accurate sample temperature measurement. The thermocouple is in direct contact with the sample. The configuration of the STA HP 3 eliminates temperature measurement errors due to sample – thermocouple distance (unlike levitating MSB-Magnetic Suspension Setup).

High speed micro heater permits rapid heating and cooling (up to 300°C/min controlled heating rate and up to 150°C/min cooling rate).

Very small furnace volume allows rapid gas changes. In addition the low volume lowers the cost of ownership (gas consumption/energy requirement) drastically.

Flexible gas dosing and security design. Our gas dosing panels can be designed to your needs. The number of gases can be selected (standard up to 3, more on request). In addition an optional vapor generator as well as an automatic evacuation and gas burn off safety system for gases like hydrogen and hydrocarbons are available.

Service Anfragen bei Linseis

 

You are interested in the STA HP 3?

You need more information?

Contact us today!

 

Send us your request >>

Specifications

Linseis TGA STA HP 3

ModelSTA HP 3
Temperature range:RT up to 1200°C
Pressure range:up to 150 bar
Sample mass:Up to 5 g
Resolution:0.1 ug
Vacuum:10E-4 mbar
TG-Sensors:Type E/K/S/B/C
TG-DSC Sensors:Type E/K/S/B/C
Electronics:Integrated or separation on electronics
Interface:USB or Ethernet
Vapor Generator:Optional
Gas Dosing:1, 2 or 3 Gases (more on request)

Gas equipment

Hochdruck Thermowaage - Gaszubehör

Gasmischanalge für Hochdruckwaagen Linseis TGA HP

Customized gas control

The LINSEIS TGA/STA HP 3 series can be equipped with any number of mass flow controllers (MFCs), depending on the customer’s needs, to control, mix and handle a wide range of gases. This allows full control of atmospheres from 10-4mbar up to 150 bar in a temperature range from room temperature up to 1200°C. Additionally, there is the possibility to add condensate traps, water vapor generators and also heated transfer lines for dosing of steam and other condensing gases. All gas control panels fulfill high German quality and safety standards and are user friendly designed to guarantee best possible performance.

Software

The all new Platinum Software greatly enhances your workflow as the intuitive data handling only requires minimum parameter input.

AutoEval offers a valuable guidance for the user when evaluating standard processes such as glass transitions or melting points. Thermal library product identification tool, provides a database with 600 polymers permitting an automatic identification tool for your tested polymer. Instrument control and/or surveillance through mobile devices gives you control wherever you are.

 

Linseis LFA 500 Software

  • Software packages are compatible with latest Windows operating system
  • Set up menu entries
  • All specific measuring parameters (User, Lab, Sample, Company, etc.)
  • Optional password and user levels
  • Undo and Redo function for all steps
  • Infinite heating, cooling or dwell time segments
  • Multiple language versions such as English, Germany, French, Spanish, Chinese, Japanese, Russian, etc. (user selectable)
  • Evaluation software features a number of functions enabling a complete evaluation of all types of data
  • Multiple smoothing models
  • Complete evaluation history (all steps can be undone)
  • Evaluation and data acquisition can be performed simultaneously
  • Data can be corrected using zero and calibration correction
  • Data evaluation includes: Peak separation software Signal correction and smoothing, first and second derivative, curve arithmetic, data peak evaluation, glass point evaluation, slope correction. Zoom / individual segment display, multiple curve overlay, annotation and drawing tools, copy to clip board function, multiple export features for graphic and data export, reference based correction

Applications

Application: Measurement of Calciumoxalate at 100bar constant pressure

The STA HP3 can be operated also at high pressures such as 100bar. The scheme shows the DSC and TG signal of a calcium oxalate run in 100 bar static nitrogen atmosphere at a linear heating rate of 20K/min up to 600°C. The red TG curve shows the first two mass loss steps that are well known for calcium oxalate.

However the first effect is shifted in temperature due to the high ambient pressure. The first effect is the loss of water, where it is notable that the enthalpy peak ends clearly after the mass loss effect which means the water is released but still need more energy to evaporate due to the high ambient pressure.

The second peak is the loss of carbon monoxide which happens at nearly the same temperature like at lower pressures. The reason is that this effect is a structural decomposition reaction that is happening independent from ambient pressure. Even if the CO is finally released it is not so much affected by the high pressure like the water in the first mass loss step as it is not in a chemical balance and part of an irreversible decomposition.

Measurement of Calciumoxalate at 100bar constant pressure in STA HP3

Application: Pressure influence on the thermal decomposition of Calciumoxalate

The substance calcium oxalate monohydrate is a common known reference material for thermo-balances and DSCs. It decomposes thermally in three definite mass loss steps that are caused by the release of water (a), the release of carbon monoxide (b) and the release of carbon dioxide (c). Also in pressurized atmospheres, these effects can be seen, however they see a pressure depending shift on the temperature axis. The scheme shows the decomposition of calcium oxalate monohydrate at 2 bar and 100 bar nitrogen atmosphere, measured by Linseis STA HP3. The first and last effect are clearly occurring later at the higher pressure (blue curve), while the second effect (b) is happening a little bit earlier. The reason is that the decomposition that releases the water and CO2 are reversible under higher pressure and therefore are delayed, while the decomposition step (b), the loss of
CO is an irreversible decomposition reaction that is independent of ambient pressure.

STA HP 3 pressure influence on the thermal decomposition of CalciumoxalateCalcium

Application: Coal gasification

A common known application for HDSC measurements is the investigation of the so called coal gasification or hydro gasification. This process, where carbon is heated in a water steam atmosphere is used in some catalytical processes, for example to remove carbon monoxide (CO) from exhaust fumes and especially to get valuable organic compounds out from resources like charcoal or biomass.

The whole process can be described like this:

Charcoal or the Carbon parts of Biomass react with water vapour to a mixture of carbon monoxide and hydrogen at higher temperatures (C + H2O CO + H2).

This process can be done with or without additional oxygen. If an oxygen containing atmosphere is used, you will also get additional carbon monoxide according to (C + O2 CO2 followed by C + CO2 2 CO) The third equation, no matter if you use oxygen or not, shows the reaction of carbon monoxide with water to get more hydrogen (CO + H2O CO2 + H2). So in the end you will get a mixture of carbon monoxide and hydrogen.

Those two gases are involved in chemical balances and therefore sometimes it is also interesting, to know how much pressure you have in your system, because the pressure determines on which side of the equation the balance will be. Finally, the purpose of the coal gasification is, that you can get methanol and methane out of the two created gases carbon monoxide and hydrogen (CO + 2 H2 CH3OH; CH3OH + H2 CH4)

That means with this process you can get from any kind of carbon to the basic building block of almost every organic compound (drugs, polymers, oils, waxes, fatty acids, organic acids and so on).

 

Application graph for TGA STA High Pressure - Coal gasification

Application: Comparison of fast heating rates

The unique furnace design of the STA HP 3 allows ultra-fast heating rates, even in pressurized experimental setups. The curves show the zero curves of an empty system at 10, 20 and 200 K/min at constant pressure of 10 bar
nitrogen. As you can see even at fast heating speed, there is the same noise level and accuracy than with slower rates. Each curve was measured twice, to show the reproducibility which is also excellent as can be seen above.

STA HP 3 comparison of fast heating rates

Downloads

STA HP 3 Product brochure PDF
Product brochure STA HP 3 (PDF)

Download